पवन FX बनाना: शोर तर्क में छनन ES1 का उपयोग

In this Quick Tutorial, we'll look at how to create a classic analog synthesis sound — the sound of whistling wind — using Logic's ES1 synth.  

इस त्वरित ट्यूटोरियल में, हम कैसे एक क्लासिक अनुरूप संश्लेषण ध्वनि हवा सीटी का उपयोग कर ध्वनि पैदा करने के लिए तर्क ES1 synth में देख लेंगे.

चरण 1 - लॉन्च ES1

तर्क खोलने और फ़ाइल को चुनने के द्वारा शुरू करो

फिर, मैं / हे निरीक्षक के नीचे छोड़ दिया पर चैनल पट्टी के अनुभाग में क्लिक करें, और डिफ़ॉल्ट EVP88 सॉफ्टवेयर साधन पर पकड़ और चुन ES1

अंत में, नीले ES1 बटन डबल - क्लिक करें ES1 विंडो खोलने:

चरण 2 - ES1 सेट

कॉन्फ़िगर के रूप में नीचे स्क्रीनशॉट में दिखाया ES1:

यहाँ सभी आवश्यक सेटिंग्स की एक सूची है, बाएँ से दाएँ और ऊपर से नीचे, और वे क्या मतलब है:

  • Mix is set to Sub only, because the Sub oscillator is the only one of the two that offers white noise. 
  • The Sub oscillator is set to Noise (the squiggly waveform). 
  • Drive is set to 0 (zero) to reduce distortion. 
  • Filter is set to '24dB classic' for the classic swept noise sound. 
  • The filter's Cutoff is set to about the middle position, but you can adjust that to taste. 
  • Resonance is also set to about the middle position. The increased Resonance is what gives you a sense of pitch and "whistly-ness" in the final sound. You can also adjust this to taste, but don't set it too high or it will self-resonate and provide too much of a sense of pitch. 
  • Key is set to the middle position, so that playing further up the keyboard will open the filter up a bit more and let you stack up multiple wind voices in different registers. 
  • In the bottom section, the Low Frequency Oscillator is set to a smoothed random waveform (the one at the 3 o'clock position), itself derived from white noise. Applying this to the Filter Cutoff will automatically vary the wind's pitch. Rate is set to 0.62 Hz; feel free to adjust this also. Higher frequencies will give you more active wind.
  • The slider to the left of the Router is set to the upper 3/4 of its range; this controls the basic amount of the Low Frequency Oscillator that is sent to control the filter's cutoff. In the Router itself, the filter's Cutoff is set as the destination for the Low Frequency Oscillator. 
  • The slider to the right of the Router is set to the lower 1/6 of its range; this sends a little more of the Low Frequency Oscillator to the filter's cutoff depending on your keyboard's trigger velocity.
  • Finally, the ADSR sliders are all set to Long or Full, or nearly so; this will give you long slow attacks and decays for your wind sound.

चरण 3 - निष्कर्ष

अब अपने मिडी कीबोर्ड पर अपनी सीमा के बीच में नोटों की एक जोड़ी, खेलते हैं और आप एक ठोस सर्दियों हवा ध्वनि सुनना चाहिए. अंतरिक्ष डिजाइनर से एक भी ghostlier ध्वनि के लिए एक लंबे reverb जोड़ने का प्रयास करें:

[ऑडियो आईडी = "6749"]

और, के रूप में हमेशा प्रयोग है, और में मज़ा है तर्क !

Richard Lainhart

More articles by this author

Richard Lainhart is an award-winning composer, filmmaker, and author. His compositions have been performed in the US, Europe Asia, and Australia, and recordings of his music have appeared on the Periodic Music, Vacant Lot, XI Records, Airglow Music, Tobira Records, Infrequency, VICMOD, and ExOvo labels. His animations and short films h... Read More


Want to join the discussion?

Create an account or login to get started!